P006C MAP - Turbocharger/Supercharger Inlet Pressure Correlation

Description and meaning of DTC p006c

This generic powertrain diagnostic trouble code (DTC) typically applies to many OBD-II vehicles. That may include but is not limited to vehicles from Toyota, Dodge, Chrysler, Fiat, Sprinter, VW, Mazda, etc. A stored code P006C means that the powertrain control module (PCM) has detected a discrepancy in the correlating signals between the manifold absolute pressure (MAP) sensor and the turbocharger/supercharger inlet pressure sensor. In some vehicle applications, the MAP sensor may be described as a barometric pressure sensor. Obviously, the code P006C is applicable exclusively to vehicles with forced air induction systems. Other stored MAP sensor or forced air induction system codes should be diagnosed and repaired before attempting to diagnose a code P006C. Intake manifold absolute pressure (air density) is measured in either kilopascal (kPa) units or inches of mercury (Hg), utilizing the MAP sensor. These measurements are input to the PCM as varying degrees of voltage. MAP and barometric pressure signals are measured in similar increments. The turbocharger/supercharger inlet pressure sensor will typically be of a similar design to the MAP sensor. It also monitors air density. It is most often positioned inside the turbocharger/supercharger inlet hose and it provides the PCM with an appropriate voltage signal reflecting such. If voltage input signals (between the MAP sensor and the turbocharger/supercharger inlet pressure sensor) differ by more than a programmed degree (over a certain period of time and under a particular set of circumstances), a code P006C will be stored, and a malfunction indicator lamp (MIL) may be illuminated. In some vehicle applications, MIL illumination may require multiple drive cycles (with a failure). Exact parameters for code storage (as it relates to the vehicle in question) can be obtained by consulting a reliable vehicle information source (such as AllData DIY).

p006c diagnostic trouble code symptoms

Symptoms of a P006C engine code may include: Reduced engine performanceDecreased fuel efficiencyHesitation or delayed engine accelerationA rich or lean conditionLouder than normal hissing/suction noise upon acceleration

DTC p006c - possible causes

Causes for this engine code may include: Defective MAP sensorFaulty turbocharger/supercharger inlet pressure sensorOpen or shorted wiring or connectorInsufficient engine vacuumRestricted air intakePCM or PCM programming error

How to fix OBD-II diagnostic trouble code p006c

I would begin with a visual inspection of all MAP sensor and turbocharger inlet pressure sensor wiring and connectors. I would also make sure that the turbocharger/supercharger inlet hoses are secure and in working order. I would inspect the air filter. It must be relatively clean and clear of obstruction. When diagnosing a code P006C, I would need a manual vacuum pressure gauge, a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of reliable vehicle information. A reasonable precursor to any MAP related code is a manual engine intake vacuum pressure test. Use the vacuum pressure gauge and get specification guidelines from your vehicle information source. If engine vacuum is insufficient, there is an internal engine malfunction that must be rectified before proceeding. Now, I would connect the scanner to the vehicle diagnostic port and retrieve all stored codes and freeze frame data. Freeze frame data provides a picture of the exact circumstances which were occurring at the instant of the malfunction which led to the stored code P006C. I would write this information down as it may be helpful as my diagnosis unfolds. Next, I'd clear the codes and test-drive the vehicle to see if the code is reset. If it is: Use the DVOM to test for a reference signal (typically 5-volts) and a ground at the MAP sensor and turbocharger/supercharger inlet pressure sensor connectorsThis can be accomplished by connecting the positive test lead of the DVOM to the reference voltage pin of the sensor connector and the negative test lead to the ground pin of the connectorIf the appropriate degree of reference voltage and a ground are discovered: I would test the MAP sensor and turbocharger/supercharger inlet pressure sensor using the DVOM and my vehicle information sourceThe vehicle information source should yield wiring diagrams, connector face views, connector pin-out charts, and diagnostic flow charts as well as component testing specificationsTest the individual sensors while they are unplugged with the DVOM placed on the ohms settingMAP and/ turbocharger/supercharger inlet pressure sensors which do not comply with manufacturer's specifications, should be considered faulty If the respective sensors are in compliance with manufacturer's specifications: With the key on and the engine running (KOER), reconnect the sensors and use the DVOM to test individual sensor signal circuit wiring directly behind the respective sensor connectorsIn order to determine if the respective sensor signals are correct, follow the air pressure to voltage charts (that should be located within the vehicle information source)If either of the sensors do not reflect a degree of voltage which falls within manufacturer's specifications (according to manifold absolute pressure and turbocharger/supercharger boost pressure), consider that sensor defectiveIf the correct MAP sensor and turbocharger/supercharger inlet pressure sensor voltage signal is present: Gain access to the PCM and test the corresponding signal circuit (for each sensor in question) at the (PCM) connector. If there is a sensor signal at the sensor connector, that is not present at the PCM connector, suspect an open circuit between the two componentsYou may disconnect the PCM (and all related controllers) and test individual system circuits using the DVOM. Follow wiring diagrams and connector pin out charts to test individual circuit resistance and/or continuitySuspect PCM failure or a PCM programing error if all MAP/ turbocharger/supercharger inlet pressure sensors and circuits are within specifications. Locating applicable technical service bulletins (TSB) may help dramatically in your diagnosisThe turbocharger/supercharger inlet pressure sensor is often left unplugged after air filter replacement and other related maintenance. If the vehicle in question has been recently serviced, check this connector first

More OBD-II diagnostic trouble codes (DTC)