P00B7 Engine Coolant Flow Low/Performance

Description and meaning of DTC p00b7

This generic powertrain diagnostic trouble code (DTC) typically applies to many OBD-II vehicles. That may include but is not limited to vehicles from Chevy, Audi, Ford, VW, etc. Anecdotally this particular code seems to be more commonly found on Chevrolet / Chevy vehicles (Sonic, Aveo, Malibu, Spark, etc. ). Anytime that I have been faced with diagnosing a code P00B7, it has meant that the powertrain control module (PCM) had detected a discrepancy in the correlating signals between the radiator coolant temperature sensor and the engine coolant temperature (ECT) sensor. This may cause the PCM to reach the conclusion that engine coolanat flow is restricted. In order to make sure that coolant is flowing as intended between the radiator and the engine cooling passages, coolant temperature in the radiator is sometimes monitored in comparison with the temperature of coolant in the engine.

p00b7 diagnostic trouble code symptoms

Symptoms of a P00B7 engine code may include:Excessively rich exhaustDrivability issuesPoor idle qualitySeriously diminished fuel efficiency

DTC p00b7 - possible causes

Causes for this engine code may include:Low coolantStuck thermostatDefective ECT sensorFaulty radiator coolant temperature sensorShorted or open circuits or connectorsBad PCM or PCM programming error

How to fix OBD-II diagnostic trouble code p00b7

An effort should be made to ensure that the engine is full of coolant and not overheating before attempting to diagnose any stored ECT sensor related codes. Before proceeding, the engine must be full of the proper coolant and not overheating under any circumstances. Cold cranking the engine and allowing the thermostat to open (while observing the temperature gauge or scanner data display) is also a good idea. A source of reliable vehicle information, a diagnostic scanner, a digital volt/ohmmeter (DVOM), and an infrared thermometer with a laser pointer will be required to diagnose a code P00B7. A visual inspection of ECT sensor and radiator coolant temperature sensor system wiring and connectors should be your next step if the engine is not overheating,. Prepare to retrieve all stored codes and freeze frame data by connecting the scanner to the vehicle diagnostic port. Once this information is retrieved, write it down as it may be helpful as you continue with the diagnosis. Next, clear the codes and test-drive the vehicle to see if the code is reset. Your vehicle information source will provide you with wiring diagrams, connector pin-out charts, component testing specifications, and connector views. These things will help you to test individual circuits and sensors with the DVOM. Test individual system circuits using the DVOM only after the PCM (and all related controllers) have been disconnected. This will help to guard against controller damage. Connector pin-out charts and wiring diagrams are particularly helpful for testing individual circuit voltage, resistance, and/or continuity. How to test the radiator coolant temperature sensor and the ECT sensor:Locate the correct component testing procedures/specifications and wiring diagram from the vehicle information sourceDisconnect the sensor to be testedPlace the DVOM on the ohms settingUse the DVOM test leads and your component testing specs to test each sensorAny sensor which does not comply with manufacturer’s specifications should be considered defectiveHow to probe for reference voltage and a ground at the radiator coolant temperature sensor and ECT sensor:With the key on and the engine off (KOEO), connect the positive test lead of the DVOM to the reference voltage pin of each sensor connector (test one sensor at a time)Use the negative test lead to probe the ground pin of the same connector (at the same time)Test for reference voltage (typically 5-volts) and a ground at the individual sensor connectorsHow to test radiator coolant temperature sensor and ECT sensor signal voltage:Reconnect the sensors Probe the signal circuit of each sensor with the positive test lead of the DVOM The negative test lead must be connected to the ground pin of the same connector or to a known good engine/battery groundUse the infrared thermometer to check actual coolant temperature at each of the sensorsYou may either use the temperature to voltage chart (found within the vehicle information source) or the data display on the scanner to determine if each sensor is functioning properly Compare actual voltage/temperature with desired voltage/temperature Each sensor should reflect actual coolant temperature or voltage. If either of them does not, suspect that it is faultyTest individual signal circuits at the PCM connector if the individual sensor signal circuits reflect the correct degree of voltage at the sensor connector. This may be done using the DVOM. If the sensor signal detected at the sensor connector is not present at the corresponding circuit of the PCM connector, an open circuit between the sensor in question and the PCM exists. Only after exhausting all other possibilities, and if all radiator coolant temperature and ECT temperature sensors and circuits are within specifications, may you suspect PCM failure or a PCM programing error. Locating technical service bulletins (TSB) which are applicable to the vehicle make and model, symptoms, and codes stored may help you with your diagnosis

More OBD-II diagnostic trouble codes (DTC)