P00B8 MAP - Mass or Volume Air Flow Correlation Bank 2

Description and meaning of DTC p00b8

This generic powertrain diagnostic trouble code (DTC) typically applies to many OBD-II vehicles. That may include but is not limited to vehicles from Land Rover, Ford, Alfa Romeo, Toyota, etc. A stored code P00B8, means that the powertrain control module (PCM) has detected a discrepancy in the correlating signals between the manifold absolute pressure (MAP) sensor and the mass or volume air flow sensor (MAF/VAF) for engine bank two. Bank 2 denotes the bank of the engine that does not contain the number one cylinder. Consult a reliable vehicle information source for the location of the #1 cylinder for the vehicle in question. Only vehicles that are equipped with multiple (one per engine bank) throttle body openings should exhibit this code. Air density (pressure) in the intake manifold is reflected using the MAP sensor which supplies the PCM with a voltage signal. This input voltage signal is received (by the PCM) as either kilopascal (kPa) units or inches of mercury (Hg). In some cases, MAP is substituted for barometric pressure and measured in similar increments. When the internal combustion engine is operating at peak efficiency, it creates a strong vacuum which must be restricted to only the throttle body opening/s. Vacuum is regulated by the throttle plate (controlled by the driver under acceleration) and the idle air control (IAC) valve when the engine is at idle. This vacuum effectively draws in the air required to complete each combustion cycle. A precise fuel to air ratio is one of the most critical factors in achieving maximum fuel efficiency and the minimization of harmful exhaust emissions in mass produced vehicles. As the throttle plate/s are opened, air entering the intake manifold is measured by either the MAF or VAF sensor/s. Fuel delivery and ignition timing strategy are calculated (by the PCM) using data contrived from these MAF or VAF sensor/s. Air which passes through these devices is referred to as metered air. Air which is involuntarily introduced to the engine (vacuum leaks) can contribute to excessively lean (too much air or not enough fuel) conditions and is called unmetered air. There are two basic types of air metering devices:MAF SensorThis type of sensor is most often used in domestic vehicles. It is based around one or more thermal resistors which are suspended in the bore of the sensor housing, so that air can flow directly across them. One of the thermal resistors monitors MAF while the other measures intake air temperature (IAT). Hot wire MAF sensors use voltage applied directly to a single resistor to monitor the amount of intake air which flows across it. As ambient air flow across the resistor is increased, the temperature of the resistor decreases resulting in a drop in the resistance level of the circuit. These changes in the resistance level of the circuit result in voltage variations which the PCM receives as a particular measure of metered air entering the engine intake manifold. Cold wire MAF sensors usually look similar to hot wire sensors and use a similar system of metering intake air. In the cold wire MAF, a pair of thermal resistors also may be used. The first is positioned in a recessed area of the sensor housing and measures only ambient air temperature, as it enters the sensor. The second thermal resistor is positioned near the center of the bore so that incoming air can flow across it, as the throttle plate is opened. When the engine is running, the PCM compares input voltage signals from each of these resistors to determine precisely how much metered air is being drawn into the engine. VAF SensorThe key difference between the MAF and the VAF is that the VAF is configured with a door or a flap that is opened by air that is drawn into the intake. This type of air metering device is used primarily in vehicles imported from Europe. At idle, the spring loaded flap is secured in the closed position. When the throttle is opened, the door is forced open. The action of the door/flap on its hinge actuates a potentiometer that transmits a voltage signal to the PCM. The PCM recognizes these variations in potentiometer voltage as the degree of metered air being drawn into the intake. A code P00B8 will be stored, and a malfunction indicator lamp (MIL) may be illuminated, if the PCM detects voltage signals between the MAP sensor and the MAF/VAF sensor (Bank 2) which differ by more than a programmed degree. MIL illumination may require multiple ignition cycles with a failure.

p00b8 diagnostic trouble code symptoms

Symptoms of a P00B8 engine code may include:Hesitation or stall upon accelerationRich or lean exhaustReduced fuel efficiencyDiminished engine performance

DTC p00b8 - possible causes

Causes for this code may include: Defective MAP sensorFaulty or contaminated MAF/VAF sensorOpen or shorted wiring or connectors in the related circuitsCracked or broken air inlet pipeInsufficient engine vacuumPCM or PCM programming error

How to fix OBD-II diagnostic trouble code p00b8

A diagnostic scanner, a digital volt/ohmmeter (DVOM), a manual vacuum pressure gauge, and a reliable vehicle information source will be required to diagnose a code P00B8. A manual engine vacuum pressure test should precede diagnosing any MAP sensor related code. This may be done using the vacuum pressure gauge. If the engine is not making sufficient vacuum, it must be repaired before moving forward with your diagnosis. Check the engine and all air inlet pipes for signs of cracking or breakage and make repairs as necessary. Vacuum leaks may contribute to the conditions which caused the P00B8 to be stored. Visually inspect all related wiring and connectors if the engine is in good working order and there are no vacuum leaks. Make repairs as required. Connect the scanner to the vehicle diagnostic port and retrieve all stored codes and freeze frame data. Write this information down as it may aid you in your diagnosis. Next, clear the codes and test-drive the vehicle to see if the code is reset. If the code is immediately reset: Test the MAP sensor and the MAF/VAF sensor (Bank 2) using the DVOM. A reliable vehicle information source may yield valuable diagnostic information like component specifications, wiring diagrams, and connector views Use the DVOM on the ohms setting to test the individual sensors while they are unpluggedSensors which fail to comply with manufacturer’s specifications should be considered defective If the sensors comply with manufacturer’s specifications: Use the DVOM to test for reference voltage (typically 5-volts) and a ground at sensor connectors Connect the positive test lead of the DVOM to the reference voltage pin of the sensor connector with the negative test lead connected to the ground pin of the connectorIf reference voltage and a ground are detected:Reconnect the sensor in question and test its signal circuit with the engine runningFollow the air pressure or air flow to voltage chart found within the vehicle information source to determine if the respective sensors are functioning properlySensors which fail to reflect the degree of voltage (according to MAP and MAF/VAF) specified by the manufacturer, should be considered faultyIf sensor signal input voltage (at the sensor connector) reflects the correct degree of voltage: Use the DVOM to test the corresponding signal circuit (for the sensor in question) at the PCM connector. If an appropriate sensor signal is discovered at the sensor connector but not at the PCM connector, suspect that there is an open circuit between the PCM and the sensor in questionDisconnect the PCM (and all related controllers) from the circuit and test individual system circuits using the DVOM. Follow the diagnostic flow chart or connector pin diagrams to test individual circuit resistance and/or continuity. Make repairs wherever requiredSuspect PCM failure or a PCM programing error if all sensors and circuits are within specifications. Check technical service bulletins (TSB) for entries which match the vehicle in question (as well as the symptoms and codes stored) to help with your diagnosisThe MAF/VAF sensor connector is frequently left unplugged after service is performed. If a P00B8 has presented immediately after air filter replacement, check this connector

More OBD-II diagnostic trouble codes (DTC)