P0298 Engine Oil Over Temperature Condition

Description and meaning of DTC p0298

This diagnostic trouble code (DTC) is a generic powertrain code, which means it applies to most OBD-II equipped vehicles including but not limited to Ford, Nissan, Suzuki, Dodge, Chevrolet, Jeep, Subaru, etc. Although generic, the exact repair steps may vary depending on make/model. A stored code P0298 indicates that the powertrain control module (PCM) has detected an engine oil temperature that is higher than acceptable. The conditions which contribute to a code of this nature being stored may be electrical or mechanical. Not every vehicle is equipped with a system that monitors oil temperature. Personally, I have only encountered oil temperature monitoring systems on diesel applications. Engine oil temperature sensors are typically negative coefficient thermistors which decrease circuit resistance as oil temperature is elevated. The oil temperature monitoring circuit begins with a reference voltage signal (usually 5-volts), applied to the sensor. When engine oil is at or near ambient temperature, oil temperature sensor resistance is high and that keeps oil temperature sensor circuit voltage low (normally near . 5-volts). As oil temperature increases, and sensor resistance decreases, circuit voltage becomes greater. The PCM is programmed to recognize these variations in sensor circuit voltage as varying degrees of oil temperature. In some cases, the engine oil temperature sensor also provides an engine oil temperature gauge with an electrical signal that is displayed on the instrument panel for driver convenience. If the PCM detects a level of engine oil temperature sensor circuit voltage that is not within the programmed parameters, a code P0298 will be stored and a malfunction indicator lamp may be illuminated.

p0298 diagnostic trouble code symptoms

A stored code P0298 should be considered urgent and diagnosed as soon as possible. The engine should not be operated until the conditions for causing this code to be stored are rectified. Symptoms of a P0298 engine code may include: Unusual engine noises and/or smellsEngine coolant leaksDiminished engine performanceEngine cooling system codes

DTC p0298 - possible causes

Possible causes for this P0298 code may include: An engine cooling system condition that has resulted in engine overheatingDefective engine oil temperature sensorOpen or shorted circuitCorroded wiring and/or connectorsLow oil level

How to fix OBD-II diagnostic trouble code p0298

Before attempting to diagnose a code P0298, I would need a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a reliable vehicle information source. While it is always a good idea to visually inspect system wiring and connectors prior to beginning your diagnosis in this case, it is most important that you make sure that the engine is full (to the appropriate limit and with the correct type) of good quality oil and engine coolant. A note about overheatingEngine overheating is the leading cause of oil over temp conditions. Engine overheating may be the result of a coolant leak, a bad thermostat, cylinder head (or gasket) malfunctions, or an air flow problem. Make sure that the engine cooling system is filled with coolant and that all of the fans are operating as intended. If the engine cooling system is more than a half-gallon low, locate the source of the coolant leak and repair it. With the engine cooling system filled with the proper coolant and working normally and the crankcase properly filled with oil, connect the scanner to the vehicle diagnostic connector and retrieve all stored codes and freeze frame data. Having this information written down can be helpful as your diagnosis proceeds. After you have made a note of all stored codes and related data, clear the codes and operate the vehicle to see if the P0298 is reset. If the engine is not overheating: And the engine oil temperature sensor code fails to reset, continue to operate the vehicle normally until the PCM enters readiness mode or the code is reset. If the PCM enters readiness mode your problems are solved. If the code is reset a malfunction persists. And the P0298 is reset, unplug the engine oil temperature sensor connector and use the DVOM to check for a reference voltage signal and a ground at the connector. Testing If there is a reference voltage signal and ground present, use the DVOM and the vehicle information source to test sensor resistance. Replace the sensor if it fails to conform to specifications. If there is no reference voltage at the sensor connector, locate the corresponding circuit at the PCM connector and use the DVOM to test for reference voltage there. If there is reference voltage at the PCM and none at the engine oil temp sensor, suspect a broken or shorted wire between the two. If there is no reference voltage at the PCM connector, suspect a defective PCM or programming error. If there is no ground at either the PCM connector or the engine oil temperature sensor connector, locate the appropriate ground junction and ensure that it is secure. A new ground can be added in a worst case scenario. Attempting to diagnose an overheating engine with a stored code P0289 is an effort in futility.

More OBD-II diagnostic trouble codes (DTC)