P040C EGR Temp Sensor A Circuit Low

Description and meaning of DTC p040c

This is a generic diagnostic trouble code (DTC) that typically applies to OBD-II vehicles. That may include but is not limited to vehicles from Mazda, VW, Audi, Mercedes Benz, Ford, Dodge, Ram, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. Before the EGR (Exhaust Gas Recirculation) systems were effectively introduced to vehicles in the 1970's, engines were actively wasting unburned fuel and expelling it to the atmosphere. These days on the other hand, a vehicle has to have a certain emission rating in order to proceed with production. The use of EGR systems has greatly improved emissions by recirculating fresh exhaust coming from the exhaust manifold and/or other parts of the exhaust system and recycling or re-burning it to make sure we are efficiently burning the fuel that we pay for with our hard earned cash! The function of the EGR temperature sensor is essentially to provide a means for the ECM (Engine Control Module) to monitor the temperature within the EGR system and/or adjust flow accordingly using the EGR valve. It does this easily using a common temperature sensitive resistor-type sensor. Your OBD (On-Board Diagnostic) scan tool may show P040C and associated codes active when the ECM detects a fault within the EGR temperature sensor or it's circuits. As I mentioned earlier, the system involves the exhaust which is hot, not only that but you are dealing with one of the hottest areas of the vehicle so be aware of where your hands/fingers are even with the engine off for a short period of time. The code P040C Exhaust Gas Recirculation Temperature Sensor A Circuit Low is set by the ECM when there is a detected a low electrical value within the EGR Temperature Sensor A circuit. Refer to a vehicle specific repair manual to determine which is the A part of the circuit for your particular application.

p040c diagnostic trouble code symptoms

Symptoms of a P040C trouble code may include:Failed smog or emissions state/provincial testEngine noise (knocking, rattling, pinging, etc. )Louder exhaustExcessive exhaust smells

DTC p040c - possible causes

Causes for this P040C engine code may include:Defective or damaged EGR (Exhaust Gas Recirculation) temperature sensorEGR temperature sensor gasket leakingCracked or leaking exhaust pipe in which the sensor is mountedBurnt wiring harness and/or sensorDamaged wire(s) (open, short to power, short to ground, etc. )Damaged connectorECM (Engine Control Module) issuePoor connections

How to fix OBD-II diagnostic trouble code p040c

Basic Step #1First thing I would do here is check for anything we can see by just visually inspecting the sensor and surrounding EGR system, looking for exhaust leaks in particular. Also check out the sensor and its harness while your in there. Remember what i said about those high temps? They can cause havoc on plastic and rubber insulated wires so inspect them thoroughly. TIP: Black soot may indicate an exhaust leak around the area. Basic Step #2 A lot of EGR issues I've seen in the past has been caused by accumulated soot in the exhaust potentially caused by a number of things (poor maintenance, low quality fuel etc. ). In this case, it is not an exception, so it may be good to clean your EGR system or at the very least the temperature sensor. Be aware that sensors mounted within the exhaust systems may feel like they are seized when trying to unfasten. Remember, these sensors are subject to substantial temperature fluctuations, so a bit of heat using an Oxyacetylene torch (not for the layman) may help loosen the sensor. Once sensor is removed, use carburetor cleaner or similar product to effectively soak the soot. Use a wire brush to loosen soot in any overly accumulated areas. When reinstalling the clean sensor, make sure to apply some anti-seize to the threads to aid in preventing seizing. NOTE: The last thing you want to do here is break the sensor inside the manifold/exhaust. This could be an expensive mistake so take it easy when cracking free the sensor. Basic Step #3Verify the integrity of the sensor by measuring actual electrical values compared to manufacturer specific desired values. Do this using your multimeter and following manufacturer specific pin-out test procedures.

More OBD-II diagnostic trouble codes (DTC)