P0539 A/C Evaporator Temp Sensor Intermittent
Description and meaning of DTC p0539
This is a generic diagnostic trouble code (DTC) and applies to OBD-II vehicles. That may include but is not limited to vehicles from Ford, Chevrolet, Dodge, Ram, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. Essentially, the air conditioning evaporator operates in the opposite sense as a condenser. The condenser converts gas to fluid and the evaporator converts fluid to gas while absorbing heat from the fan air flowing through it in the process. It's purpose is to remove heat from the air inside the cabin, in turn reducing the temperature inside the car. The functionality of the A/C evaporator temperature sensor is crucial to the proper operation of your HVAC (Heating, Ventilation and Air Conditioning) system. The ECM (Engine Control Module) uses electrical values from this sensor to adjust the temperature inside according to your needs, in coordination with your evaporator among other A/C components. The ECM activates P0539 and associated codes (P0535, P0536, P0537, and P0538) when it detects an outside of desired electrical range condition within the A/C evaporator temperature sensor or it's circuits. This could equally be mechanical or an electrical problem, Always keep in mind the environment of the sensor (any sensor for that matter), it could be subjected to an environment posed with unique issues. P0539 A/C Evaporator Temperature Sensor Circuit Intermittent code is set when the ECM detects an intermittent malfunction within the A/C evaporator temperature sensor or it's circuit(s).
p0539 diagnostic trouble code symptoms
Symptoms of a P0539 trouble code may include: No cold air blowing from the air ventsFan air temperature erratic/fluctuatingA/C compressor clutch not engagingHVAC system not functioning as desired
DTC p0539 - possible causes
Causes for this P0539 code may include:Defective or damaged A/C Evaporator coreDefective A/C Evaporator Temperature sensorDefective ECM ( Engine Control Module)Wiring issue within the sensor's circuitWiring harness connector issueIntermittent electrical connectionInternal resistance (corrosion, damaged harness, overheated circuit, etc. . )
How to fix OBD-II diagnostic trouble code p0539
Be sure to check for technical service bulletins (TSBs) for your vehicle. Getting access to a known fix can save you time and money during diagnosis. Basic Step #1Locate and visually inspect the A/C evaporator temperature sensor. Generally speaking the evaporator core is located inside the HVAC (heating ventilation and air conditioning) air box. The A/C Evaporator Temperature sensor is typically mounted to the evaporator itself or very near it. You may be able to gain access by looking under the dash fairly easily. It may also be possible that you will need to remove numerous plastic panels and/or the radio so always refer to your service manual for the specific location. Keep an eye out for any signs of overheating and/ or corrosion on the sensor itself. This may indicative of your problem. If found defective, replace the sensor. TIP: Make sure that your interior is at a reasonable temperature. Start prying on cold plastic and it will break so be careful. Basic Step #2Test the temperature sensor. Most times, these sensors are a resistor type sensor. In other words, the resistance within the sensor changes in direct relation to the temperature. Understanding how this works probably gives you some idea on how to diagnose the sensor itself. Usually, the manufacturer will have a desired resistance at certain temperatures. Using your multimeter you can record the resistance within the sensor and compare it to the desired values specified by your manufacturer. If an open is present, you may have an internal resistance within the sensor itself and will need to be replaced. NOTE: Your manufacturer may have a specific diagnostic strategy depending on which type of sensor, make, model, etc. so always refer to your service manual. If uncomfortable with electrical testing and/or working around refrigeration systems for that matter, bring your vehicle to a reputable shop. Basic Step #3Check the wiring. Given the location of the evaporator temperature sensor, it may be easy to locate and follow the harness to check for any obvious signs of damage. Especially around where the driver and passengers feet may interfere with the wiring (if possible).