P0613 TCM Processor

Description and meaning of DTC p0613

This generic powertrain diagnostic trouble code (DTC) typically applies to many OBD-II vehicles. That may include but is not limited to vehicles from Chrysler, Dodge, Jeep, Audi, Land Rover, etc. A stored code P0613 means that the transmission control module (TCM) has detected an internal control processor malfunction. In some cases, the TCM may be separate from the powertrain control module (PCM). Most frequently, it is integrated into the PCM. This saves automakers space, time, and money. Each time the ignition is turned on and the PCM is energized, multiple controller self-tests are performed. In addition to running internal controller self-tests, the controller area network (CAN) is used to compare signals from each individual module to ensure that the various controllers are interacting properly. In monitoring TCM function, if the PCM detects a problem, a code P0613 will be stored and a malfunction indicator lamp (MIL) may be illuminated. Depending upon the perceived severity of the malfunction, multiple failure cycles may be necessary for MIL illumination.

p0613 diagnostic trouble code symptoms

Symptoms of a P0613 trouble code may include:Erratic transmission shift patternsHarsh transmission shiftingInoperable or inaccurate speedometer/odometerOther stored TCM/PCM codes

DTC p0613 - possible causes

Causes for this code may include:Faulty TCM/PCM TCM/PCM programming errorOpen or shorted circuit or connectors in the CAN harnessFailed TCM/PCM power sourceInsufficient control module ground

How to fix OBD-II diagnostic trouble code p0613

Unfortunately, even the most experienced and well-equipped professional technician may find diagnosing a code P0613 to be quite a challenge. There is also the issue of reprogramming. Without the necessary reprogramming equipment, it will be impossible to replace a defective controller and complete a successful repair. If TCM/PCM power supply codes are present, they will need to be repaired before attempting to diagnose a P0613. There are several preliminary tests that can be performed prior to declaring any controller defective. A diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of reliable vehicle information will be required. Connect the scanner to the vehicle diagnostic port and retrieve all stored codes and freeze frame data. You will want to write this information down, just in case the code proves to be an intermittent one. After recording all pertinent information, clear the codes and test drive the vehicle until the code is reset or the PCM enters readiness mode. If the TCM/PCM enters readiness mode, the code is intermittent and will be more difficult to diagnose. The condition, which caused the P0613 to be stored, may even need to worsen before a diagnosis can be made. If the code is reset, continue with this short list of preliminary tests. When attempting to diagnose a P0613, information may be your greatest tool. Search your vehicle information source for technical service bulletins (TSB) that parallel the code stored, vehicle (year, make, model, and engine), and symptoms exhibited. If you find the right TSB, it may yield diagnostic information that will aid you in a major way. Use your source of vehicle information to obtain connector face views, connector pin-out charts, component locators, wiring diagrams, and diagnostic flow charts related to the code and vehicle in question. Use the DVOM to test controller power supply fuses and relays. Replace blown fuses as required. Fuses should be tested with the circuit loaded. If all fuses and relays appear to be functioning as intended, a visual inspection of controller related wiring and harnesses is in order. You will also want to check chassis and engine ground junctions. Use your vehicle information source to obtain ground locations for related circuits. Use the DVOM to test ground integrity. Visually inspect system controllers for signs of water, heat, or collision damage. Any controller that is damaged, especially by water, should be considered defective. If controller power and ground circuits are intact, suspect a defective controller or a controller programming error. Controller replacement will require reprogramming. In some cases, you may purchase reprogrammed controllers through aftermarket sources. Other vehicles/controllers will require on-board reprogramming that may only be done through a dealership or other qualified source. Unlike most other codes, the P0613 is likely caused by a defective controller or a controller programming errorTest system ground integrity by connecting the negative test lead of the DVOM to ground and the positive test lead to battery voltage

More OBD-II diagnostic trouble codes (DTC)