P0833 Clutch Pedal Switch B Circuit

Description and meaning of DTC p0833

This generic powertrain diagnostic trouble code (DTC) typically applies to all OBD-II vehicles equipped with a clutch pedal. That may include but is not limited to vehicles from Jaguar, Dodge, Chrysler, Chevy, Saturn, Pontiac, Vauxhall, Ford, Cadillac, GMC, Nissan, etc. Although generic, the specific repair steps may vary depending on make/model. The P0833 OBD-II trouble code is associated with the Clutch Pedal Switch B Circuit. When the Powertrain Control Module (PCM) detects a malfunction within the Clutch Pedal Switch B Circuit, also known as the clutch position sensor or clutch start switch circuit a number of different codes can be set. These codes are P0830, P0831, P0832, P0833, P0834, P0835 and P083F based on the specific malfunction that alerts the PCM to set the code and illuminate the Check Engine Light. The purpose of the Clutch Pedal Switch B Circuit is for the PCM to monitor the position of the clutch pedal. This process is accomplished by reading the output voltage of the clutch position sensor. The clutch position sensor switch may vary in design from one vehicle to another, it is usually a basic on/off switch mounted near the clutch foot pedal on the support bracket. Regardless of the design, constant voltage is typically present on one side of the switch and the contacts are closed by engaging the clutch pedal transferring voltage to the starter or starter solenoid. This basic circuit and switch prevents starting the engine prior to engaging the clutch. Code P0833 Clutch Pedal Switch B Circuit is set by the PCM when the Clutch Pedal Switch B Circuit is open or has a general malfunction. Refer to a vehicle specific repair manual to determine which is the B circuit for your particular vehicle.

p0833 diagnostic trouble code symptoms

Symptoms of a P0833 engine code may include: The engine will not startThe engine will start without engaging the clutchCheck Engine Light illuminated

DTC p0833 - possible causes

Causes for this code may include: Faulty clutch position sensor switchBlown fuse or fuse-able link (if applicable)Corroded or damaged connectorFaulty or damaged wiringFaulty PCM

How to fix OBD-II diagnostic trouble code p0833

The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins (TSB's) for the specific vehicle by year, model and power plant. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. The second step is to locate the clutch position sensor switch and look for obvious physical damage. Perform a thorough visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots. Next is to check the connectors and connections for security, corrosion and damaged pins. This process must include all wiring connectors and connections to the clutch position sensor switch, PCM, starter and the starter solenoid. Consult the specific tech data for the vehicle to see if a fuse or fuse-able link is incorporated into the circuit. Advanced StepsThe advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. Voltage requirements will very based of the specific year and model of the vehicle. Voltage ChecksWhen the clutch is disengaged there should be appropriately 12 volts on one side of the switch. When the clutch is engaged you should have voltage on both sides of the switch. The starter solenoid or starter should also have power based on the configuration. If this process identifies the absence of a power source or ground, continuity testing may be required to check the integrity of the wiring and the clutch position sensor switch. When the clutch is engaged you should have continuity through the switch and when the clutch is released the meter should indicate no continuity through the switch. Continuity tests should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.

More OBD-II diagnostic trouble codes (DTC)