P2094 B Camshaft Position Actuator Control Circuit Low Bank 2

Description and meaning of DTC p2094

This is a generic powertrain diagnostic trouble code (DTC) and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Subaru, Cadillac, Dodge, Mazda, Audi, Mercedes, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. OBD-II diagnostic code P2094 is associated with the B camshaft position actuator control circuit on bank 2. When the Engine Control Unit (ECU) detects improper signals within the B camshaft position actuator control circuit code, P2094 will be set and the check engine light will be illuminated. Some vehicles may require multiple failure cycles before the check engine light is illuminated. The purpose of the camshaft position actuator control circuit is to monitor variations of between the camshaft/s and the crankshaft and send a corresponding signal to the ECU. This process is accomplished with camshaft and crankshaft position sensors which convert varying degrees between the camshaft/s and the crankshaft into a voltage signal that is used by the ECU to adjust the timing and optimize the performance of the engine. This code is defined as B Camshaft Position Actuator Control Circuit Low Bank 2 and indicates a detected low electrical condition within the B camshaft position actuator control circuit on bank 2 as mentioned earlier. Note: The A camshaft is either the intake, left, or front camshaft. Conversely, the B camshaft is either the exhaust, right, or rear camshaft. Left/Right and Front/Rear are determined as though you are sitting in the driver's seat. Bank 1 is the side of the engine that contains the #1 cylinder, whereas bank 2 is the opposite bank. If the engine is an inline or straight design, there is only one bank.

p2094 diagnostic trouble code symptoms

Symptoms of a P2094 trouble code may include: Rough engine idleDecreased oil pressureEngine may misfirePoor engine performanceIncreased fuel consumptionChange oil or service soon light is illuminatedCheck engine light illuminated

DTC p2094 - possible causes

Causes for this P2094 code may include: Worn timing belt or chainDefective camshaft variable timing solenoidDefective variable valve timing actuatorEngine oil level is too lowBlown fuse or fuse-able link (if applicable)Misalignment of timing componentsCorroded or damaged connectorFaulty or damaged wiringFaulty ECU

How to fix OBD-II diagnostic trouble code p2094

The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins (TSB's) for the specific vehicle by year, model and engine combination. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. The second step is to check the oil level and the condition of the oil. The proper oil pressure plays a key role in the function of this circuit. Then locate all of the components within this circuit and perform a thorough visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots. Next is to check the connectors for security, corrosion and damaged pins. This process must include all associated sensors, components and the ECU. Advanced StepsThe advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. Other ideal tools for this situation are a timing light and an oil pressure gauge. Voltage requirements will vary based on the specific year and model of the vehicle. Timing ChecksThe timing must be checked using the appropriate test equipment and the settings must be precise for the engine to operate correctly. An incorrect timing reading is an indication that essential timing components such as the belt, chain or gears may be worn or damaged. If this code is exhibited immediately after a timing belt or chain replacement, then you can suspect misalignment of timing components as the possible cause. Voltage ChecksThe camshaft and crankshaft sensors are typically supplied with a voltage reference of approximately 5-volts from the ECU. If this process identifies the absence of a power source or ground, continuity testing may be required to check the integrity of the wiring, connectors and other components. Continuity tests should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance. Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.

More OBD-II diagnostic trouble codes (DTC)