P20BB Reductant Heater A Control Circuit Low

Description and meaning of DTC p20bb

This diagnostic trouble code (DTC) is a generic powertrain code and applies to many diesel OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Ford, Mercedes Benz, Sprinter, Audi, Ram, Chevrolet, Dodge, BMW, GMC, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. A stored code P20BB means that the powertrain control module (PCM) has detected insufficient voltage in the control circuit for the on-board reductant heater designated with the letter A. This designation is used where multiple reductant heaters are in use, consult a vehicle specific repair manual to determine which is the A circuit for your application. The catalyst system is responsible for reduction of (basically) all the other exhaust emissions although certain applications are also equipped with a NOx trap. Exhaust gas recirculation (EGR) systems go another step further in the reduction of NOx. Nevertheless, today’s larger and more powerful diesel engines cannot meet strict federal (U. S. ) emission standards with the EGR, diesel particulate filter/catalytic converter, and NOx trap alone. It was for this reason that selective catalytic reduction (SCR) systems were invented. SCR systems inject a reductant compound or a diesel exhaust fluid (DEF) into the exhaust in front of the diesel particulate filter and/or the catalytic converter. The precisely timed DEF injection elevates the temperature of the filtration element and allows it to perform more efficiently. It makes the filtration element last longer and allows fewer harmful exhaust emissions to be released into the atmosphere. The entire SCS system is monitored and controlled by either the PCM or a stand-alone controller (which interacts with the PCM). Either way, the controller monitors the O2, NOx, and exhaust temperature sensors (as well as other inputs) to determine the appropriate time for DEF (reductant) injection. Precise DEF injection is necessary to maintain exhaust temperature within acceptable parameters and optimize pollutant filtration. Reductant heaters are used to prevent diesel exhaust fluid from freezing during extreme temperatures. These heaters are typically located in the DEF reservoir and/or the reductant injector supply hose/s. If the PCM detects insufficient voltage on the control circuit for reductant heater A, a code P20BB will be stored and a malfunction indicator lamp may be illuminated.

p20bb diagnostic trouble code symptoms

Symptoms of a P20BB trouble code may include:Diminished engine performanceExcessive black smoke from vehicle exhaustReduction in fuel efficiencyOther SCR related codes

DTC p20bb - possible causes

Causes for this code may include:Bad reductant heaterOpen or shorted circuits in the reductant heater controlDefective reductant temperature sensorBad SCR controller/PCM or programming error

How to fix OBD-II diagnostic trouble code p20bb

You will need access to a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of vehicle specific diagnostic information to diagnose a code P20BB. If you can find a technical service bulletin (TSB) that matches the vehicle year, make, and model as well as the engine size, code/s stored, and symptoms exhibited, it could yield helpful diagnostic information. You will want to begin your diagnosis with a visual inspection of the reductant heater system harnesses and connectors. Burnt or damaged wiring and or connectors should be repaired or replaced before proceeding. Proceed by hooking the scanner to the vehicle diagnostic connector and retrieving all stored codes and pertinent freeze frame data. Write this information down before clearing the codes and test driving the vehicle until the PCM either enters readiness mode or the code is reset. The code is intermittent and may be much more difficult to diagnose (at this time), if the PCM enters readiness mode. If this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made. Should the code be reset, search your source of vehicle information to obtain diagnostic flow charts, connector pin out charts, connector face views, as well as component testing procedures and specifications. This information will be required to complete the next step of your diagnosis. Use the DVOM to test the power supply to the SCR control system/. Test fuses with the circuit loaded to avoid misdiagnosis. If the appropriate power (battery voltage) and ground circuits are discovered, use the scanner to activate the reductant heater/s and test output control circuit voltage. If voltage is insufficient, suspect that the controller is bad or has experienced a programming error. If the voltage output circuit is within parameters, use the DVOM to test the reductant heater element in question. If the heater fails to meet manufacturer’s specifications, suspect that it has failed. If this code is exhibited in warm weather, suspect that a programming error has occurred

More OBD-II diagnostic trouble codes (DTC)